FIXING DYNAMO STARTER

The condition of the most annoying is when it's rush hour, the entry is already a budget and the car could not start. When important conditions are in fact could not. Certainly it feels you want to kick the car many times. It's not kicked because better vetted in advance. Usually, this problem occurs on a system generating electricity. There are several causes of a car starter is weak. Here's the cause and how to repair the starter Dynamo when the car's weight.

Causes Of Car Starter Dynamo Weight

Check The Battery

May supply electricity from the shortage of Dynamo car battery. Note the constituent components of the car battery. Usually, the car battery which is already damaged, when start, the sound is "tech, tech, tech" that pretty quickly. This happens because water aki under the standard. When the battery is low, the cells in the battery. Then the arch makes the positive and negative pole touching each other so shorted and unable to save electricity.

Check the positive and negative Cables

Check for a loose cable and corrosion. Due to a loose cable and corrosion resulting in weak power. There are some signs of dry battery car soak. Quite a lot of the problems that it causes. To prevent worse damage, you need to know how to care for dry battery. For the insights, you need to know the types of the car battery. If you want to buy a new battery then consider tips on choosing car battery.

How To Troubleshoot A Car Starter Dynamo Weight

There are several solutions to handle the heavy car starter Dynamo if the root of the problem is the battery. Try the water content of the battery back and try to clear the corrosion. If it is still difficult to starter, reel in electricity. Find other car battery is still normal and don't forget to make sure that the capacity of the two batteries that are appropriate. Don't forget to bring your jumper cables. If you are a manual transmission car, trying to push the car to trigger the movement of the machine. Turn on the contact, press the clutch and push his car. After a few meters, try off the clutch pedal. Usually, the car engine could live.

Damage to the solenoida might cause heavy car starter for dinamo. Generally occurs in a roll that is pull in or hold the coil in a coil. When damaged, the ability of magnetism to hold the pinion will be reduced. As a result of the starter pinion gear instead of moving backward. Carbon brush is exhausted as a result can not connect a pull in a coil with the ground. Would pull in coil can't push the pinion gear, reels in the starter doesn't work and even some other effects. Better take it to a repair shop to fix it.

The cause of heavy third car starter Dynamo may be located on the starter switch contacts. Switch the starter suffered keuasan due to worn constantly. The effects of wear and tear is marked by the terdengarnya sound of the "superficial" when the machine distarter. The solution is to replace it with a new one. It costs roughly around two hundred to three hundred thousand dollars.

To replace, prepare some tools and materials. For the material is certainly a new starter switch. For the Prod key 14 shock, 12 key rings (or a combination) and 10 key fitting, ring or a combination.

To remove, open the negative battery pole clamps so as not happening to short when removing the starter terminal clamps. Off the terminal clamp nut 12 so the starter can be open. Then, off the starter solenoid connector. Use key 14 to remove the two starter bolts that connect the starter with the machine.

Some cars use three bolts. Collect bolt in the tray so that it does not disappear. For installation, locate the newly purchased components that fit in place. Installation process upside down with its yesteryear.

If you only through puddles or flooding DOS high, then there is a possibility that the water can damage the carburetor. Before, you need to know the components of the carburetor car, the workings of the car and the carburetor problems carburetor system. Try off the carburetor and check, whether or not filled with water. If it is full of water, then you can reset it at the buoy.

The closure of the carburetor and remove the valve needles. If severe damage, then there are other ways rather than replaced. Now I see you buoy types. If in hollow then check with shake or clean before the valve. If bubbles appear, it means the leak. Don't forget to install the negative battery pole. Then did the test and turn on the machine can work.

There are two kinds of Setup where the buoy the highest and lowest. If you want the highest position, first install the appropriate buoy system is its location. Do the installation close the carburetor to a vise with its axis vertical and the lid's position above. Measure the distance between the surface of the CAP the carburetor until the tip of the body of the buoy. If the size is less fitting, then the Middle tongue bendable system of buoys.

Set up with the help of two pliers so that the float is not damaged and do not hold the body of the buoy. If you want the lowest position, then the longest distance measurement between the surface close to the carburetor end buoy. Do the same way to fix that is by two tang. There are certain tips for how to adjust the carburetor more efficient gasoline car.